John Deere Products & Services D100 User Manual download pdf (Page 48)

Installing

1. Slide right side hood pivot into tractor bracket with hood in open

position (left side pivot will slide into place as hood closes) and slowly

close hood.

2. Connect wiring harness.

3. Close hood.

Cleaning Plastic Surfaces

IMPORTANT: Improper care of machine plastic surfaces can

damage that surface:

• DDoo nnoott wwiippee ppllaassttiicc ssuurrffaacceess wwhheenn tthheeyy aarree ddrryy.. DDrryy wwiippiinngg

wwiillll rreessuulltt iinn mmiinnoorr ssuurrffaaccee ssccrraattcchheess..

• UUssee aa ssoofftt,, cclleeaann ccllootthh ((bbaatthh ttoowweell,, ddiiaappeerr,, aauuttoommoottiivvee

mmiitttt))..

• DDoo nnoott uussee aabbrraassiivvee mmaatteerriiaallss,, ssuucchh aass ppoolliisshhiinngg

ccoommppoouunnddss,, oonn ppllaassttiicc ssuurrffaacceess..

1. Rinse hood and entire machine with clean water to remove dirt and

dust that may scratch the surface.

2. Wash surface with clean water and a mild liquid automotive washing

soap.

IMPORTANT: Insect repellent spray may damage plastic and painted

surfaces. Do not spray insect repellent near machine.

3. Dry thoroughly to avoid water spots.

4. Wax the surface with a liquid automotive wax. Use products that

specically say “contains no abrasives.”

IMPORTANT: Do not use a power buffer to remove wax.

5. Buff applied wax by hand using a clean, soft cloth.

Cleaning and Repairing Metal Surfaces

Cleaning:

Follow automotive practices to care for your vehicle painted metal

surfaces. Use a high-quality automotive wax regularly to maintain the

factory look of your vehicle’s painted surfaces.

Repairing Minor Scratches (surface scratch):

1. Clean area to be repaired thoroughly.

IMPORTANT: Do not use rubbing compound on painted surfaces.

2. Use automotive polishing compound to remove surface scratches.

3. Apply wax to entire surface.

Repairing Deep Scratches (bare metal or primer showing):

1. Clean area to be repaired with rubbing alcohol or mineral spirits.

2. Use paint stick with factory-matched colors available from your

authorized dealer to ll scratches. Follow directions included on paint

stick for use and for drying.

3. Smooth out surface using an automotive polishing compound. Do not

use power buffer.

4. Apply wax to surface.

Removing and Installing Front Wheel

Assembly

Removing:

1. Park machine safely. (See Parking Safely in the SAFETY section.)

CAUTION: The machine can fall or slip from an unsafe lifting

device or supports.

• UUssee aa ssaaffee lliiffttiinngg ddeevviiccee rraatteedd ffoorr tthhee llooaadd ttoo bbee lliifftteedd..

• LLoowweerr mmaacchhiinnee oonnttoo jjaacckk ssttaannddss oorr ootthheerr ssttaabbllee ssuuppppoorrttss

aanndd bblloocckk wwhheeeellss bbeeffoorree sseerrvviicciinngg..

IMPORTANT: Place jack stands under frame, not under

transmission or engine, when raising or supporting machine.

GXAL42051—UN—04MAR13

2. Safely lift and support machine. Place safe lifting device under end of

front hanger bracket at location (A), and place jack stands or other

stable supports under frame on each side at location (B). Block

wheels remaining on the ground to prevent machine movement.

GXAL42052—UN—04MAR13

3. Remove plastic cap (C) from end of wheel hub.

Service Miscellaneous

1 2 ... 43 44 45 46 47 48 49 50 51 52 53 ... 63 64

Comments to this Manuals

No comments

John Deere Products & Services D100 User Manual Page 48

Comments to this Manuals